[crw-talk] Luther Pen Turn agenda

[griff]

I used the 10" Jet and had to leave early, I left my mandrel and pen 
turning hollow live center in the 10" Jet along with my Slimline 
bushings, Triple EEE finish and friction polish as well as a small pen 
assembly board next to Luther's pen press.  Aaron was going to collect 
them for me and return them at the next meeting.  When I was using that 
lathe, I did not notice Duane's 7MM spacer nor the Oneway live center.  
Hope Duane's stuff turns up.  j

On 11/22/23 2:45 PM, wisawdust wrote:
> Members, I got home and started unpacking and noticed I was missing a 
> 7mm spacer.  This was a longer spacer, approx 1" long.  Also I was 
> missing a Oneway live center.  It was on the 10" club lathe.  Please 
> check your stuff for the two items.  Thanks
>
> Duane
>
>
>
> Sent from my Galaxy
>
>
> -------- Original message --------
> From: griff <griff at mwt.net>
> Date: 11/20/23 10:26 AM (GMT-06:00)
> To: crw-talk at crwoodturner.com
> Subject: Re: [crw-talk] Luther Pen Turn agenda
>
> Members, James has put together a wonderful event.  I hope all of us 
> who are mobile or somewhat mobile make it.  Or even for a while.  My 
> tools are sharp, packed and ready to send chips flying.  I have 
> friction polish, paper towels and evidently a third press as well.  
> (My homemade Harbor Freight Special).
>
> I have not read anything about face shields for the students, I am 
> bringing mine and a pair of side shield safety glasses.
>
> I assume we come in one of the doors on the west side of the building 
> and head to the shop.
>
> John
>
> On 11/19/23 4:32 PM, James Bloomer wrote:
>> Timeline for the turn
>>
>> 1100 arrival and setup
>> 1200 safety brief, introduction for group and begin.
>> 1200-1500 hands on turn with Luther HS woods students
>> 1500 begin tear down, possibly take a few left over kits and we turn 
>> and finish them.
>> 1600 complete tear down and clean up
>> Timeline is fluid dependent on kits available and number of students.
>> Bring your quick finish of choice (beeswax, carnuba, Capt 
>> Eddie's..etc) something to give some protection.
>> Currently tracking, myself Jay, John . Possibly Aaron and Duane.
>> All are welcome to either chat about turning or help assemble pens. I 
>> will bring my press, and Jay usually does as well
>>
>> The last two have been excellent in the terms of student turn out and 
>> Interest.
>>
>>
>> Please respond if you can make it out even for a short time to assist.
>>
>> In Service
>> Jim Bloomer
>>
>> _________________________________________
>> Use "Reply to All" or "Reply List" to reach the whole group, "Reply" goes only to sender.
>> ______
>> crw-talk mailing list
>> crw-talk at crwoodturner.com
>> http://crwoodturner.com/mailman/listinfo/crw-talk_crwoodturner.com
>> Check the archive to make sure your message was sent:http://crwoodturner.com/pipermail/crw-talk_crwoodturner.com/
>
> _________________________________________
> Use "Reply to All" or "Reply List" to reach the whole group, "Reply" goes only to sender.
> ______
> crw-talk mailing list
> crw-talk at crwoodturner.com
> http://crwoodturner.com/mailman/listinfo/crw-talk_crwoodturner.com
> Check the archive to make sure your message was sent: http://crwoodturner.com/pipermail/crw-talk_crwoodturner.com/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://crwoodturner.com/pipermail/crw-talk_crwoodturner.com/attachments/20231123/7ad239f9/attachment.html>