[Crw-talk] Vacuum chucking questions

Greg Haugen greg.haugen at ymail.com
Sun Jul 1 20:42:21 CDT 2012


Surplus Center pumps are some times ok.  Their inventory changes alot.  Right now, they don't have much.  Possibly one option (1/4 hp model but there's no cord, etc.), but for the $200 range, I'd go with the one from Stubby Lathe USA.  Sometimes Surplus has them in the $50-80 range but watch these, they're fairly beaten up and are often the 0522 model which is the 220 Volt model.  The ones in the catalogs are the 0523 model and 110V.  

https://www.surpluscenter.com/sort.asp?catname=&byKeyword=yes&search=gast%20pump


Also a small nitpick, Craft Supplies is the only place that offers them with a switch on the cord itself.  Packards do not have a switch so they'll have to be plugged/unplugged for on/off or you'll have to add a switch.  Craft Supplies are well thought out the way they have them set up.

Greg



________________________________
 From: "Ldsolem at aol.com" <Ldsolem at aol.com>
To: greg.haugen at ymail.com; griff at mwt.net; crw-talk at crwoodturner.com 
Sent: Sunday, July 1, 2012 6:37 PM
Subject: Re: [Crw-talk] Vacuum chucking questions
 

I purchased my Gast pump from the Surplus Center in Nebraska a few years 
back and I do not remember what I paid but it was a lot less then $400 
dollars.
 
I would give the Surplus Center a call and ask them if they have the pump. 
1-800-488-3407.
 
Lyle  Solem
 
 
In a message dated 7/1/2012 2:19:41 P.M. Central Daylight Time, 
greg.haugen at ymail.com writes:
My opinions are below in your questions.
>
>
>How satisfactory are the vacuum devices that run off an air  compressor?  I'm told they are very loud.  Is a vacuum pump a better  direction to go?  They are loud and I  just don't feel like their in the same league as a vacuum pump.
>
>How reliable are used vacuum pumps?  I 
  see them on eBay for about $45 or so.  Used pumps can be as good but they are a  gamble.  What were the pumps used for prior and how well were they  cleaned after use?  There are many variables to consider.  They're  not bad but not always good either.
>
>
>Are the pumps used by HVAC 
  technicians to draw the air out of air conditioning systems 
  satisfactory?  Depending on the size,  possibly.  Like the used pumps there are a lot of variables.
>
>
>When it comes to pumps, Gast's model  0523 is the pump that is in the catalogs for $440.  It's the best of the  best.  There are parts available if the user does have problems.  If  you do a search on ebay for Gast 0523 Pump you'll find some options, again a  lot of variables.  IF you order one, expect shipping in the $30 to $40  range alone.  There is another pump available that has been getting some  good reviews and is half the price and is a "New" pump so there are no  questionable variables about useage.  Stubby Lathe USA carries it as well  as some adaptors (the adaptors are made of delrin and will need to be turned  down smaller to fit our lathes).  Here's a link to them.  http://stubbylatheusa.com/cgi-bin/onlinestore.py
>
>
>Also there are many articles on Vacuums  around.  Some are overly complicated, in my opinion.  It doesn't  need to be.  Keep it simple.
>
>
>This is just my 2 cents on the  subject.
>
>
>Greg
>
>
>
>
>________________________________
> From: John & Donna Griffiths  <griff at mwt.net>
>To: crw-talk at crwoodturner.com 
>Sent: Sunday, July 1, 2012 2:02  PM
>Subject: [Crw-talk] Vacuum  chucking questions
>
>Hello all, I have some 
  questions:
>
>How satisfactory are the vacuum devices that run off an air 
  compressor?  I'm told they are very loud.  Is a vacuum pump a better 
  direction to go?
>
>How reliable are used vacuum pumps?  I see them 
  on eBay for about $45 or so.
>
>Are the pumps used by HVAC technicians to 
  draw the air out of air conditioning systems 
  satisfactory?
>
>John
>
>
>_________________________________________Use 
  Reply to All to reach the whole group, Reply goes only to 
  sender.
>______
>Crw-talk mailing list
>Crw-talk at crwoodturner.com
>http://crwoodturner.com/mailman/listinfo/crw-talk_crwoodturner.com
>
>
>
>
>_________________________________________Use 
  Reply to All to reach the whole group, Reply goes only to 
  sender.
>______
>Crw-talk mailing 
  list
>Crw-talk at crwoodturner.com
>http://crwoodturner.com/mailman/listinfo/crw-talk_crwoodturner.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://crwoodturner.com/pipermail/crw-talk_crwoodturner.com/attachments/20120701/032abc9f/attachment-0001.htm>


More information about the Crw-talk mailing list